TÀI LIỆU SỐ
Danh mục TaiLieu.VN
Kết quả 5893-5904 trong khoảng 6251
Tinh luyện khử khí và loại bỏ tạp chất phi kim trong sản xuất hợp kim nhôm
Trong nấu luyện nhôm và hợp kim nhôm , nhôm lỏng phản ứng tức thì với O2, CO, CO2, cũng như phản ứng với nước hấp phụ, nước trong màng hydroxyt trên bề mặt liệu và với hơi nước trong môi trường khí lò tạo oxyt nhôm và hydro làm tăng hàm lượng tạp chất Al2O3 và hydro trong kim loại, thường lượng hydro này vượt quá giới hạn hòa tan của hydro trong...
8 p bvu 20/11/2017 444 1
Trong công trình này chúng tôi tập trung vào đánh giá phân bố rỗng thấm cùa khối trung tâm và khối phía bắc. Qua kết quả nghiên cứu thể hiện tính bất đồng nhất về rỗng thấm của đá móng tuy nhiên quy luật chung vẫn không thay đổi, khu vực phía bắc mỏ giá trị độ rỗng thấm có thay đổi so với các nghiên cứu trước.
9 p bvu 20/11/2017 164 1
Bài giảng Vẽ kỹ thuật cơ khí: Chương 2 - Mối ghép chặt đinh tán, hàn và dán
Nội dung bài giảng "Chương 2 - Mối ghép chặt đinh tán, hàn và dán" sẽ cung cấp cho các bạn khái niệm, phân loại và phạm vi sử dụng đinh tán, hàn và dán. Mời các bạn tham khảo
13 p bvu 20/11/2017 392 1
Bài báo này trình bày kết quả nghiên cứu số hạng điều chỉnh thiết kế áo cơ sở nữ Việt Nam cho đa dạng vóc dáng sử dụng phần mềm thiết kế trang phục 3 chiều V- Stitcher. Nghiên cứu được thực hiện trên 67 sinh viên nữ có số đo vòng ngực 80±0.5cm. Kết quả nghiên cứu đã chia ra được 7 nhóm cơ thể từ mẫu đo từ việc phân tích thành phần...
11 p bvu 20/11/2017 236 1
Phương pháp điều khiển sliding mode và droop control cho các bộ nghịch lưu trong Microgrid
Trong bài này trình bày phương pháp điều khiển trượt bám SMC (Sliding Mode Control) để điều khiển các bộ nghịch lưu kết nối song song trong một microgrid hoạt động độc lập, bộ điều khiển này có thể cải thiện được đặc tính bền vững của hệ thống điều khiển và giảm sai số xác lập. Tính ổn định của hệ thống vòng kín được xác định theo...
11 p bvu 20/11/2017 268 1
Ảnh hưởng kích thước hình học của ứng xử trụ tròn thành mỏng chịu tải va đập dọc trục vận tốc thấp
Ảnh hưởng kích thước hình học trụ tròn thành mỏng lên các kiểu biến dạng khi chịu tải va đập dọc trục vận tốc thấp được nghiên cứu bằng phương pháp mô phỏng số. Mô hình là các mẫu trụ tròn nhôm 6060-T5 với các đường kính (D), độ dày (h) và chiều dài (L) khác nhau. Với tỉ lệ D/h và L/D thay đổi, trụ tròn có các kiểu biến dạng đối...
9 p bvu 20/11/2017 277 2
Thiết kế chế tạo thiết bị thí nghiệm kiểm tra đặc tính ma sát và độ chịu mài mòn của lớp bề mặt
Việc kiểm tra đánh giá chất lượng và tính chất các lớp bề mặt đóng vai trò quan trọng, đặc biệt khi công nghệ phủ tăng bền bề mặt ngày càng được ứng dụng rộng rãi. Bài báo này trình bày về một nghiên cứu chế tạo thiết bị kiểm tra đặc tính ma sát và mòn lớp bề mặt Pin-on-dics (POD). Loại thiết bị chế tạo ra có cấu tạo và nguyên lý...
8 p bvu 20/11/2017 499 4
Nghiên cứu cấu trúc động học của một tay máy công nghiệp dư dẫn động dạng chuỗi
Bài báo này đề xuất một cấu trúc động học mới cho một tay máy công nghiệp dư dẫn động dạng chuỗi. Đây là một cơ cấu tay máy mới được phát triển dựa trên ý tưởng cải tiến rôbốt công nghiệp 6 trục IRB 2400 của ABB. Tay máy được đề xuất gồm 6 khớp quay và 2 khớp chuyển động tịnh tiến.
10 p bvu 20/11/2017 369 3
Bài báo này giới thiệu kết quả nghiên cứu nhấp nhô bề mặt của thép làm khuôn sau gia công thô và gia công tinh bằng PMEDM sử dụng bột titan. Ảnh hưởng của nồng độ bột titan trộn trong dung dịch điện môi đến nhấp nhô bề mặt (Ra) được khảo sát trong gia công thô, đồng thời phương trình hồi quy mô tả mối quan hệ này và giá trị Ra tối ưu...
7 p bvu 20/11/2017 191 1
Trong tính toán móng cọc, việc xem xét và đánh giá tương tác giữa cọc và đất nền là rất cần thiết, đặc biệt đối với nền đất yếu, công trình có tải trọng bề mặt lớn, vì khi đó xuất hiện yếu tố có tác động tiêu cực đến sự làm việc của cọc là hiện tượng ma sát âm. Do vậy, việc xem xét và có kể đến thành phần ma sát âm trong tính...
5 p bvu 20/11/2017 193 1
Điều khiển bám hệ truyền động bánh răng với bộ điều khiển dự báo có ràng buộc
Bài báo giới thiệu một phương pháp thiết kế bộ điều khiển dự báo phản hồi trạng thái để điều khiển bám ổn định hệ truyền động qua bánh răng có các điều kiện ràng buộc. Bộ điều khiển dự báo của bài báo sử dụng mô hình xấp xỉ tuyến tính của hệ truyền động bánh răng và sử dụng hàm mục tiêu dạng toàn phương có tham số biến...
9 p bvu 20/11/2017 345 1
Nghiên cứu ảnh hưởng của thông số thiết kế hệ thống treo đến độ êm dịu xe đua F-SAE
Để đánh giá các ảnh hưởng này, một mô hình dao động không gian của xe được xây dựng dựa trên cơ sở các thông số kỹ thuật của xe đua F-SAE do TNUT sản xuất năm 2013. Phần mềm Matlab-Simulink7.04 được sử dụng để mô phỏng và tính toán các thông số ảnh hưởng. Các kết quả nghiên cứu cho thấy sự phối hợp hợp lý giữa thông số độ cứng và...
6 p bvu 20/11/2017 196 1
Bộ sưu tập nổi bật